Cen Tech Digital Multimeter 69096 Manual

Cen-Tech 7 Function Digital Multimeter. ESYNIC Digital Multimeter True RMS Auto/Manual Ranging Capacitance Tester Amp Ohm Volt Meter with Alligator Clips LED. Originally recorded March 22, 2014. This is a review of the Harbor Freight Cen-Tech 7 Function Digital Multimeter, Item # 6. It likely also applies to its bigger brother, the 7 Function.

• 7 FUNCTION DIGITAL MULTIMETER 69096 OPERATING INSTRUCTIONS Visit our Web site at REV 12a Copyright 2011 by Harbor Freight Tools. All rights reserved. © ® No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Download game pepsi man ps1 for pc. • Safety Warnings and Precautions WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.

Warnings continued on page 3. SKU 69096 For replacement parts, please call 1-800-444-3353. • Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not operate properly. SKU 69096 For replacement parts, please call 1-800-444-3353. • Do not test voltage on AC circuits higher than 750 volts. Do not test voltage on DC circuits higher than 1000 volts.

Do not test current on circuits higher than 10 amps. SKU 69096 For replacement parts, please call 1-800-444-3353. • Measure DC conductors carrying up to 1000 VDC. Turn the Range Selector Switch to 1000 DCV setting. Follow the directions above under “AC Voltage Measurements”, only use the DC settings instead. SKU 69096 For replacement parts, please call 1-800-444-3353. • Plug the red Test Lead into the VΩmA (Center) Jack.

Plug the black Test Lead into the Com (Bottom) Jack. Switch the Multimeter ON.

Connect the red probe to the anode of the diode and the black to the cathode. SKU 69096 For replacement parts, please call 1-800-444-3353. • Pull battery/fuse out of unit and replace with the same. (9V battery or 500mA/250V fast-acting fuse) Replace cover and retighten screws.

NOTE: No replacement parts are available for this tool. SKU 69096 For replacement parts, please call 1-800-444-3353.

An electrically savvy handyman frequently carries a digital multimeter in his tool box or service vehicle. A properly used multimeter measures both voltage and current for alternating current, or AC.

The multimeter also measures voltage and current for direct current, or DC. Electronic hobbyists can also test diodes, resistors and transistors with the Cen-Tech 92020 digital multimeter. Safety-conscious workmen and hobbyists receive prior instruction in the multimeter’s operation, as the device measures potentially deadly electrical voltages.

Measuring AC Voltage Place the red lead’s plug end into the jack marked “V-ohm-mA.” Place the black lead’s plug end into the jack marked “COM.” Set the multimeter to read AC voltage. Turn the range selector knob to the position marked “750 ACV.” Turn the meter on. Slide the power switch to the “On” position. Touch each probe to the item for which voltage is being measured. Use the probe ends of the leads. Do not allow your fingers to touch the probes, as lethal voltage may be present.

Read the digital display’s indicated voltage. Adjust the range selector knob to a lower range if the voltage is less than 200 volts. Turn the meter off. Slide the power switch to the “Off” position. Measuring DC Voltage Place the red lead’s plug end into the jack marked “V-ohm-mA.” Place the black lead’s plug end into the jack marked “COM.” Set the multimeter to read DC voltage.

Turn the range selector knob to the position marked “1,000 VDC.” Turn the meter on. Slide the power switch to the “On” position. Touch each probe to the item for which voltage is being measured. Use the probe ends of the leads. Do not allow your fingers to touch the probes, as lethal voltage may be present. Read the digital display’s indicated voltage.

Adjust the range selector knob to a lower range if the voltage is less than 200 volts. Turn the meter off. Slide the power switch to the “Off” position. Measuring DC Current Place the red lead’s plug end into the jack marked “10A.” Place the black lead’s plug end into the jack marked “COM.” Set the multimeter to read DC current.

Turn the range selector knob to the “10A” position. Turn the meter on. Slide the power switch to the “On” position. Touch each probe to the item for which current is being measured. Use the probe ends of the leads.